[. . . ] Owner's manual Mode d'emploi Bedienungsanleitung Istruzioni per l'uso Gebruiksaanwijzing Manual de instrucciones Bruksanvisning Manual de instruções DXZ668RMP CD/MP3/WMA RECEIVER / CeNET CONTROL RÉCEPTEUR CD/MP3/WMA : COMMANDE CeNET CD/MP3/WMA EMPFÄNGER/CeNET-STEUERUNG LETTORE CD/MP3/WMA CON RICEVITORE/ CONTROLLO CeNET CD/MP3/WMA RADIO/CeNET BEDIENING RECEPTOR Y REPRODUCTOR DE CD/MP3/WMA/ CONTROL DE CeNET CD/MP3/WMA-RECEIVER MED CeNET-KONTROLL RECEPTOR DE CD/MP3/WMA/CONTROLO CeNET Thank you for purchasing this Clarion product. Please read this owner's manual in its entirety before operating this equipment. After reading this manual, be sure to keep it in a handy place (e. g. , glove compartment). Check the contents of the enclosed warranty card and keep it carefully with this manual. [. . . ] Press any one of the [DIRECT] buttons to call out the regional station. If the reception condition of the called out station is bad, press the [DIRECT] button of the same number. The unit receives a local station on the same network. Auto store function for TP stations You can automatically store up to 6 TP stations into preset memory. If the number of TP can be received less than 6, broadcast stations already stored in memory and left without being overwritten. As "TA" lit in the display, press and hold the [ ] button for 2 seconds or longer. The TP stations with the good reception sensitivity are stored into preset memory. Even if you select FM1 or FM2, a TP station is stored into memory for FM3. PTY This function enables you to listen to a broadcast of the selected programme type even if the unit is on a function mode other than radio. Some countries do not yet have PTY broadcast. In the TA standby mode, a TP station has priority over a PTY broadcast station. The factory default setting is "OFF". TA (Traffic Announcement) In the TA standby mode, when a traffic announcement broadcast starts, the traffic announcement broadcast is received as top priority regardless of the function mode so you can listen to it. Traffic programme (TP) automatic tuning is also possible. This function can only be used when "TP" is lit in the display. When "TP" is lit, this means that the RDS broadcast station being received has traffic announcement programmes. Setting the TA standby mode If you press the [TA] button when only "TP" is lit in the display, "TP" and " TA" light in the display and the unit is set into the TA standby mode until a traffic announcement is broadcast. When a traffic announcement broadcast starts, "TRA INFO" appears in the display. If you press the [TA] button while a traffic announcement broadcast is being received, the traffic announcement broadcast reception is cancelled and the unit goes into the TA standby mode. Cancelling the TA standby mode As "TP" and " TA" lit in the display, press the [TA] button. The "TA" in the display goes off and the TA standby mode is cancelled. If "TP" is not lit, pressing the [TA] button searches for a TP station. 1. Press and hold the [ADJ] button for 1 second or longer to switch to the RDS adjustment selection display. Press the [å, ] lever upward or downward to select " PTY". ON: "PTY" in the display lights and PTY standby mode is turned on. When the selected PTY broadcast starts, the PTY item name appears in the display. OFF: "PTY" in the display goes off and PTY standby mode is cancelled. Cancelling a PTY interrupt broadcast Press the [TA] button during the PTY interrupt broadcast, the PTY interrupt is cancelled and the unit returns to PTY standby mode. Searching for a TP station When "TP" is not lit, if you press the [TA] button, "TA" in the display lights and the unit automatically receives a TP station. Note: · If a TP station is not received, the unit continues the search operation. Pressing [TA] button again goes off "TA" in the display and stops TP station searching. Selecting PTY 1. [. . . ] If the amplifiers turn off before all wires are attached, use an external relay to provide remote-on voltage (excessive current required). Turn off the power, then press the [RELEASE] button and remove the DCP. Press the reset button for about 2 seconds with a thin rod. Reset button General Nothing happens when buttons are pressed. Display is not accurate. The microprocessor has malfunctioned due to noise, etc. DCP or main unit connectors are dirty. [. . . ]